| EMQ 深沟球轴承 |
 |
| 地址: 浙江省.嘉善县. 陶庄镇夏湖大道333号 |
|
电 话: +86 573 8486 0885 传 真: +86 573 8486 0881 移动电话: 139 6823 0098 |
|
E-mail: admin@aemeke.com Http:// www.ottbearing.com |
| 台湾OTT销售办事处： |
| 台湾高雄市807三民區應安街67巷1號1樓 |
| 電話：07-380-8698 |
技术资料 >>
# 轴承的配合
1.配合的目的
配合的目的在于使轴承内圈或外圈牢固地与轴或轴承座固定,以免在互相配合面上出现不利的周向滑移。这种不利的周向滑移(称作蠕动) 会引起异常发热、配合面磨损(进而使磨损铁粉侵入轴承内部) 以及振动等各种问题，使轴承不能发挥作用。
因此对于轴承来说，由于承受负荷旋转，一般必须让套圈过盈配合使之可靠地与轴或外壳固定。
因此对于轴承来说，由于承受负荷旋转，一般必须让套圈过盈配合使之可靠地与轴或外壳固定。
2.轴及轴承座的尺寸公差与配合
公制系列的轴及轴承座孔的尺寸公差以ISO286为基准，从中选定尺寸公差即可确定轴承与轴或轴承座的配合。
轴及轴承座孔的尺寸公差与P0级精度的轴承的配合关系如图1所示。
轴及轴承座孔的尺寸公差与P0级精度的轴承的配合关系如图1所示。
3.配合的选择
选择配合时，应充分考虑轴承的使用条件。 考虑的项目大致如下 ：
·负荷的性质与大小
·运转时的温度分布
·轴承内部游隙
·轴等轴承座的加工质量、材质及壁厚结构
·安装与拆卸方法
·是否需要利用配合面吸收轴的热膨胀
·轴承的型式与尺寸 下面3 结合上述各项目，说明一下配合的选择。
·负荷的性质与大小
·运转时的温度分布
·轴承内部游隙
·轴等轴承座的加工质量、材质及壁厚结构
·安装与拆卸方法
·是否需要利用配合面吸收轴的热膨胀
·轴承的型式与尺寸 下面3 结合上述各项目，说明一下配合的选择。
1) 负荷性质的影响
轴承负荷可分为内圈旋转负荷，外圈旋转负荷及不定向负荷，其与配合的关系如表2所示
2)负荷大小的影晌
内圈在径向负荷作用下 ，半径方向即被压缩又有所伸展 ，周长趋于微小增加 ，因此初始过盈将减少。
过盈减少量可由下列计算
过盈减少量可由下列计算
因此，当径向负荷为重负荷（超过co值的25%) 时，配合必须比轻负荷时紧。
若是冲击负荷，配合必须更紧 。
若是冲击负荷，配合必须更紧 。
3）配合面粗糙度的影晌
若考虑配合面的塑性变形 ，则配合后的有效过盈受配合面加工质量的影晌 ，近似地可用下列表示 。
4）温度的影晌
一般来说 ，运转时的轴承温度高于周边温度 ，而且轴承带负荷旋转时 ，内圈温度高于轴温，因此热膨胀将使有效过盈减少。
现设轴承内部与轴承座周边的温度为 △T ，则可假定内圈与轴 配合面的温差近似为 （0.10~0.15）△T。
因此温差产生的过盈减少量△d，可由下式计算：
现设轴承内部与轴承座周边的温度为 △T ，则可假定内圈与轴 配合面的温差近似为 （0.10~0.15）△T。
因此温差产生的过盈减少量△d，可由下式计算：
因此，当轴承温度高于轴温时，配合必须变紧。
另外，在外圈与轴承座之间 ，由于温差或线膨胀系数的不同反过来有时过盈也会变化 。因此在考虑利用外圈与轴承座配合面之间的滑动吸收轴的热膨胀时，需要加以注意。
另外，在外圈与轴承座之间 ，由于温差或线膨胀系数的不同反过来有时过盈也会变化 。因此在考虑利用外圈与轴承座配合面之间的滑动吸收轴的热膨胀时，需要加以注意。
5） 配合产生的轴承内部最大应力
轴承采用过盈配合安装时， 套圈会膨胀或收缩，从而产生应力。应力过大时，有时套圈会破裂，需要加以注意 。配合产生的轴承内部最大应力可由表3的公式计算，作为参考值，取最大过盈不超过轴径的1/1000，或由表3的计算式得到的最大应力σ不大于120MPa为安全。
6） 其他
旋转精度要求特别高时，应提高轴和轴承座的精度，与轴相比，一般轴承座难加工，精度低，因此放松外圈与轴承座的配合为宜。采用中空轴及薄壁轴承座时，配合必须比通常紧。采用剖分型轴承座时，应放松与外圈的配合。对于铸铝或轻合金轴承座，配合必须比通常紧一些，这时请与OTT联系。
# 4 推荐配合
如1节所述 ，为选择合适的配合，必须考虑轴承负荷的性质及大小、温度、安装与拆卸方法等各种因素。但在实际确定配合时，还需要参考以往的经验 。
公制系列轴承的常用配合如表4.所示。各类轴承最常用的推荐配合如表5-表8所示。
公制系列轴承的常用配合如表4.所示。各类轴承最常用的推荐配合如表5-表8所示。
# 深沟球轴承的主要尺寸精度
| Nominal Inside Diameter d (mm) | Single Plane Averaged I.D.Error dmp |
Bs . Cs | Nominal Outside Diameter D (mm) | Dmp single Plane Averaged O.D.Error | |||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Grade 0 | Grade 6 | Grade 5 | Grade 4 | Grade 0 and 6 | Grade 5 and 4 | Grade 0 | Grade 6 | Grade 5 | Grade 4 | ||||||||||||||
| Over | Up-to | Up | Down | Up | Down | Up | Down | Up | Down | Up | Down | Up | Down | Over | Up-to | Up | Down | Up | Down | Up | Down | Up | Down |
| 2.5 | 10 | 0 | -8 | 0 | -7 | 0 | -5 | 0 | -4 | 0 | -120 | 0 | -40 | 6 | 18 | 0 | -8 | 0 | -7 | 0 | -5 | 0 | -4 |
| 10 | 18 | 0 | -8 | 0 | -7 | 0 | -5 | 0 | -4 | 0 | -120 | 0 | -80 | 18 | 30 | 0 | -9 | 0 | -8 | 0 | -7 | 0 | -5 |
| 18 | 30 | 0 | -10 | 0 | -8 | 0 | -6 | 0 | -5 | 0 | -120 | 0 | -120 | 30 | 50 | 0 | -11 | 0 | -9 | 0 | -7 | 0 | -6 |
| 30 | 50 | 0 | -12 | 0 | -10 | 0 | -8 | 0 | -6 | 0 | -120 | 0 | -120 | 50 | 80 | 0 | -13 | 0 | -11 | 0 | -9 | 0 | -7 |
| 80 | 120 | 0 | -15 | 0 | 13 | 0 | -10 | 0 | -8 | ||||||||||||||
# 深沟球轴承的径向游隙 (pm)
| Nominal Inside Diameter | Group MC | Group MC2 | Group MC3 | Group MC | Group MC5 | Group MC6 | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Over | Up-to | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. |
| - | 9 | 0 | 5 | 3 | 8 | 5 | 10 | 8 | 13 | 13 | 20 | 20 | 28 |
| Nominal Inside Diameter | Group C2 | Group CM (motor only) | Standard Group CN | Group C3 | Group C4 | Group C5 | |||||||
| Over | Up-to | ||||||||||||
| 10 | 0 | 7 | 3 | 10 | 2 | 13 | 8 | 23 | 14 | 29 | 20 | 37 | |
| 10 | 18 | 0 | 9 | 4 | 11 | 3 | 18 | 11 | 25 | 18 | 33 | 25 | 45 |
| 18 | 24 | 0 | 10 | 5 | 12 | 5 | 20 | 13 | 28 | 20 | 36 | 28 | 48 |
| 24 | 30 | 1 | 11 | 5 | 12 | 5 | 20 | 13 | 28 | 23 | 41 | 30 | 53 |
| 30 | 40 | 1 | 11 | 9 | 17 | 6 | 20 | 15 | 33 | 28 | 46 | 40 | 64 |
| 40 | 50 | 1 | 11 | 9 | 17 | 6 | 23 | 18 | 36 | 30 | 51 | 45 | 73 |
# 轴承振动和噪音
| Bearing Inside Diamster |
Single Bearing Vibration (Acceleration) Limit Value dB |
Single Bearing Vibration (Speed) Limit Value μm/s |
|||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Diameter series O |
Diameter series 2 |
Diameter series 3 |
V | V1 | V2 | V3 | V4 | ||||||||||||||||||||||
| d(mm) | Z | Z1 | Z2 | Z3 | Z | Z1 | Z2 | Z3 | Z4 | Z | Z1 | Z2 | Z3 | Z4 | L | M | H | L | M | H | L | M | H | L | M | H | L | M | H |
| 5 | 37 | 36 | 34 | 30 | 38 | 37 | 34 | 32 | - | 39 | 37 | 35 | 33 | - | 110 | 72 | 60 | 74 | 48 | 40 | 58 | 36 | 30 | 35 | 21 | 18 | 32 | 11 | 11 |
| 6 | 37 | 36 | 34 | 30 | 38 | 37 | 34 | 32 | - | 39 | 37 | 35 | 33 | - | 110 | 72 | 60 | 74 | 48 | 40 | 58 | 36 | 30 | 35 | 21 | 18 | 32 | 1 1 | 11 |
| 7 | 39 | 38 | 35 | 31 | 40 | 38 | 36 | 34 | - | - | - | - | - | - | 130 | 96 | 80 | 92 | 66 | 54 | 72 | 48 | 40 | 44 | 28 | 24 | 38 | 12 | 12 |
| 8 | 39 | 38 | 35 | 31 | 40 | 38 | 36 | 34 | - | - | - | - | - | - | 130 | 96 | 80 | 92 | 66 | 54 | 72 | 48 | 40 | 44 | 28 | 24 | 38 | 12 | 12 |
| 9 | 41 | 40 | 36 | 32 | 42 | 40 | 37 | 35 | - | - | - | - | - | - | 130 | 96 | 80 | 92 | 66 | 54 | 72 | 48 | 40 | 44 | 28 | 24 | 38 | 12 | 12 |
| 10 | 43 | 42 | 38 | 33 | 40 | 42 | 39 | 35 | 30 | 46 | 44 | 40 | 37 | 32 | 160 | 120 | 100 | 120 | 80 | 70 | 90 | 60 | 50 | 55 | 35 | 30 | 45 | 14 | 15 |
| 12 | 44 | 43 | 39 | 34 | 45 | 43 | 39 | 35 | 30 | 47 | 45 | 40 | 37 | 32 | 160 | 120 | 100 | 120 | 80 | 70 | 90 | 60 | 50 | 55 | 35 | 30 | 45 | 14 | 15 |
| 15 | 45 | 44 | 40 | 35 | 46 | 44 | 41 | 36 | 31 | 48 | 46 | 42 | 38 | 33 | 210 | 150 | 120 | 150 | 100 | 85 | 110 | 78 | 60 | 65 | 46 | 35 | 52 | 18 | 18 |
| 17 | 46 | 44 | 40 | 35 | 47 | 45 | 41 | 36 | 31 | 49 | 47 | 42 | 38 | 33 | 210 | 150 | 120 | 150 | 100 | 85 | 110 | 78 | 60 | 65 | 46 | 35 | 52 | 25 | 25 |
| 20 | 47 | 45 | 41 | 36 | 48 | 46 | 42 | 38 | 33 | 50 | 48 | 43 | 39 | 34 | 260 | 190 | 150 | 180 | 125 | 100 | 130 | 100 | 75 | 80 | 60 | 45 | 60 | 25 | 25 |
| 25 | 48 | 46 | 42 | 38 | 49 | 47 | 43 | 40 | 36 | 51 | 49 | 44 | 41 | 37 | 260 | 190 | 150 | 180 | 125 | 100 | 130 | 100 | 75 | 80 | 60 | 45 | 60 | 30 | 32 |
| 30 | 49 | 47 | 43 | 39 | 50 | 48 | 44 | 41 | 37 | 52 | 50 | 45 | 42 | 38 | 300 | 240 | 190 | 200 | 150 | 130 | 150 | 120 | 100 | 90 | 75 | 60 | 70 | 35 | 40 |
| 35 | 51 | 49 | 45 | 41 | 52 | 50 | 46 | 43 | 39 | 54 | 52 | 47 | 44 | 40 | 300 | 240 | 190 | 200 | 150 | 130 | 150 | 120 | 100 | 90 | 75 | 60 | 70 | 42 | 45 |
| 40 | 53 | 51 | 46 | 42 | 54 | 52 | 47 | 44 | 40 | 56 | 54 | 49 | 45 | 41 | 360 | 300 | 260 | 240 | 180 | 160 | 180 | 150 | 130 | 110 | 90 | 80 | 82 | 50 | 50 |
| 45 | 55 | 53 | 48 | 45 | 56 | 54 | 49 | 46 | 43 | 58 | 56 | 51 | 47 | 44 | 360 | 300 | 260 | 240 | 180 | 160 | 180 | 150 | 130 | 110 | 90 | 80 | 82 | 60 | 60 |
| 50 | 57 | 54 | 50 | 47 | 58 | 55 | 51 | 48 | 45 | 60 | 57 | 53 | 49 | 46 | 420 | 320 | 320 | 280 | 200 | 200 | 210 | 160 | 160 | 125 | 100 | 100 | 95 | 70 | 70 |
# 深沟球轴承的密封结构
Comparison of Our Dust-proof and Sealing Bearing Performance (Reference Only)
| Structure | Cage Type (ZZ) | Non-contact Rubber Sealing Ring (RZ) | ?Contact Rubber Sealing (RS) |
| Friction Torque | Small | Small | Because of contact sealing, Models RS1 and RS2 are bigger than Models ZZ and RZ and Model RS3 is the biggest. |
| High Speed Performance | Good | Good | Because the limit of contact sealing. (RS 3 has a high temperature rise) |
| Grease Sealing | Good | Better than Model RZ | A little better than Model RZ but Model RS1 is better than Model RS2 and Model RS3 is better than Model RS1. |
| Dust-proof | Good | Better than Model ZZ (could be used in some dust environment) | The Best {could be used in most dust condition) but Model RS2 is superior to Model RS1 and Model RS3 is superior to Model RS2. |
| Water Resistance | Unsuitable | ?Unsuitable | Good (could be used in splash condition) |
| Range of Application Temperature | -10~+110℃ | -10~+110℃ | -10~+110℃ |
Note: The description is for standard products only. However, the range of application temperature could be extended if you select cold resistant or hot resistant grease and rubber. Please contact Aemeke if you have any special requirement.
# 油脂列表
| Manufacturer | Brand | Viscosity | Base oil | Drop Point ℃ |
Consitency | Temperature range ℃ |
NMB |
| Esso | Beacon 325 | Lithium | Diester | 193 | 290 | -60 -+120 | LG20 |
| AC 205 | Nathium | Mineral | -25- -+120 | ||||
| Andok B | Nathium | Mineral | 260 | 280 | -40- -+120 | LG38 | |
| Andok C | Nathium | Mineral | >260 | 205 | -20- -+120 | LG39 | |
| Andok 260 | Nathium | Mineral | 200 | 250 | -30- -+150 | LG71 | |
| Andok RB300 | Lithium Calcium | Mineral | 175 | 300 | -30- -+100 | ||
| KYODO | NS Hilube | Lithium | Diester | 190 | 255 | -40- -+130 | LY72 |
| YUSHI | Multemp PS2 | Lithium | Diester | 189 | 280 | -50- - +110 | LY121 |
| Multemp SRL | Lithium | Ester | 191 | 245 | -40- -+150 | ||
| Multemp SC-A | Urea | >260 | 280 | 0~ +160 | |||
| Multemp ET150 | Urea | Mineral | >260 | 280 | -10- -+160 | ||
| Oneluba | Lithium | Diester Mineral | 198 | 370 | -10- - +110 | ||
| Adrex | Lithium | Mineral | 198 | 300 | -10- -+120 | ||
| Parmax | Mineral | 180 | 300 | -10- -+120 | |||
| Emalibe 1130 | Urea | Mineral | >260 | 300 | -10- -+130 | ||
| Unilube DL1 | Lithium | Mineral | 185 | 332 | -10- - +110 | ||
| Alumix HD1 | Mineral | 247 | 335 | 0~ +120 | |||
| Kluber | Staburage NBU12 | Barium | Mineral | 220 | 270 | -35- -+150 | |
| lsoflexNBU15 | Barium | Diester Mineral | 220 | 280 | -60- +130 | ||
| AsonicGLY32 | Lithium | Sythetic | -50- +140 | ||||
| AsonicGHY72 | Polyhamstoff | Ester Mineral | -40- +180 | ||||
| Is of lex super LDS18 | Lithium | Diester | 190 | 280 | -60- +130 | ||
| Is of lex super TEL | Lithium | Ester Mineral | -65 -+70 | LY218 | |||
| lsoflexLDS18 SpezialA | Lithium | Diester | 190 | 280 | -60- +130 | ||
| lsoflexPDB38CX100 | Lithium | Ester | -70- +120 | ||||
| Is of lex Top as NB52 | Barium | Sythetic hydrocarbon | 240 | 280 | -60- +170 | ||
| Barrierta L55/2 | Fluorotelomer | Fluorinated | 280 | -35- +260 | |||
| Barrierta EL | Fluorotelomer | Fluorinated | 280 | -50- +180 | |||
| Barrierta IMI/V | Fluorotelomer | Fluorinated | -50- +220 | ||||
| UnisilikonTK44N2 | Na-komplex | Silicone | 280 | -60- +230 | |||
| Dow Corning | Molykote 33M | Lithium | Silicone | 210 | -70- +180 | LY81 | |
| Molykote 44M | Lithium | Silicone | 204 | -40- +200 | LY13 | ||
| Molykote 55M | Lithium | Silicone | 260 | -55- +165 | LY52 | ||
| Molykote BR2 plus | Lithium | Mineral | 260 | -30- +150 | |||
| Molykote FS1292 | Fluorotelomer | Phlorosicone | >232 | -40- +200 | LY59 | ||
| Molvkote FS3451 | Fluorotelomer | Phlorosicone | >260 | 280 | -40- +230 | ||
| Shell | Alvania No.2 | Lithium | Mineral | 182 | 310 | -25- +120 | LY83 |
| Alvania No.3 | Lithium | Mineral | 183 | 285 | -20- +135 | LY84 | |
| Alvania RA | Lithium | Mineral | 183 | 272 | -25- +120 | LY18 | |
| Alvania EP2 | Lithium | Mineral | 185 | 233 | -10- +100 | ||
| Sunlight 2 | Lithium | Mineral | 196 | 252 | -20- +120 | ||
| Dolium R | Mineral | 238 | 276 | -20- +140 | LY119 | ||
| Aero shell NO.5 | Microgel | Mineral | >260 | 273 | -10- +130 | LG35 | |
| Aero shell NO.7 | Microgel | Diester | >260 | 281 | -70- +150 | LG49 | |
| Aero shell N0.15A | Fluorotelomer | Silicone | >260 | 282 | -70- +260 | ||
| Mobil Oil | Mobilux2 | Lithium | Mineral | 190 | 288 | -20- +120 | |
| Mobigrease 22 | Lithium | Diester Mineral | 192 | 280 | -50- +140 | ||
| Mobigrease 28 | Bentonite | Sy nthetichyd rocarb on | >260 | 280 | -60- +180 | LY48 | |
| Mobibex 47 | Mineral | >260 | 274 | -20- +120 | |||
| Du Pont | Krytox 240AC | Fluorotelomer | Fluorinated | 280 | -35- +280 | LY101 | |
| Krytox 283AC | Fluorotelomer | Fluorinated | 280 | -35- +280 | |||
| Krvtox 143AC | Fluorotelomer | Fluorinated | 282 | -35- +280 | LY115 | ||
| Toray ilicone | SH44M | Lithium | Silicone | 210 | 229 | -40- +180 | |
| SH33L | Lithium | Silicone | 210 | -70- +140 | |||
| SH41 | Lithium | Silicone | 260 | -10- +200 | |||
| Caltex | Chevron SRI-2 | Urea | Mineral | 300 | -30- + 175 | LY75 | |
| General leotrio | Anderol SRI-2 | Lithium | Diester | 280 | -60- +150 | ||
| Versilube G-300 | Lithium | Silicone | 293 | -70- +230 | LY15 | ||
| Versilube F-50 | Silicone | -70- +230 | LY5 |
# 油脂列表
| 制作厂 Manufacturer |
牌号 Brand |
增稠剂 Viscosity |
基油 Base oil |
滴点 Drop point℃ |
稠度 Consistency |
使用温度范围 Operating termperature range |
选用原则 Selection criteria |
NMB 代码 Code |
Code Exxon |
Beacon 325 | 锂基 (Lithium) | 双酯 (Diester) | 193 | 290 | -60~+120 | 低温脂 Low-temperature grease | LG20 |
| AC205 | 钠基 (Nathium) | 矿物 (Mineral) | -25~+120 | 常温脂 Normal temperature grease | ||||
| Andok B | 钠基 (Nathium) | 矿物 (Mineral) | 260 | 280 | -40~+120 | 常温脂 Normal temperature grease | LG38 | |
| Andok 260 | 钠基 (Nathium) | 矿物 (Mineral) | 200 | 250 | 30~+150 | 常温脂 Normal temperature grease | LG71 | |
| Arapen RB300 | 锂基 (Lithium) | 矿物 (Mineral) |
200 | 250 | -30~+100 | 常温脂 Normal temperature grease | ||
| Polyrex EM | 双聚尿 (Diurea) | 矿物 (Mineral) | 260 | 288 | -40~+180 | 髙温低噪音 High temperature low noise | ||
| Potyrex EP2 | 聚尿 (Ureal) | 矿物 (Mineral) | 280 | 280 | -40~+180 | 髙温低噪音 High temperature low noise | ||
| UNIREX N2 | 锂皂复合系 (Lithium complex) |
矿物 (Mineral) | 250 | 280 | -40~+180 | 髙温低噪音 High temperature low noise | ||
| UNIREX N3 | 锂皂复合基 (Lithium complex) |
矿物 (Mineral) | 250 | 235 | 40~+180 | 髙温低噪音 High temperature low noise | ||
| Kyodo Yushi |
NS Hilube | 锂基 (Lithium) | 双酯 (Diester) | 190 | 255 | -40~+130 | 常温脂 Normal temperaturo grease | |
| Muttemp PS2 | 锂基 (Lithium) | 双酯 (Diester) | 188 | 280 | -50~+110 | 低温脂 Low-temperature grease | LY72 | |
| Multemp SRL | 锂基 (Lithium) | 酯 (Ester) | 191 | 245 | -40~+150 | 低噪音脂 Low noise grease | LY121 | |
| Multemp SC-A | 聚尿 (Ureal) | ≥260 | 280 | 0~+160 | 常温脂 Normal temperature grease | |||
| Multemp ET150 | 聚尿 (Ureal) | 矿物 (Mineral) | ≥260 | 280 | -10~+160 | 常温脂 Normal temperature grease | ||
| Oneluba | 锂基 (Lithium) | 双酯 - 矿物 (Diester Mineral) | 198 | 270 | -10~+110 | 常温脂 Normal temperature grease | ||
| Adrex | 锂基 (Lithium) | 矿物 (Mineral) | 198 | 300 | -10~+120 | 常温脂 Normal temperature grease | ||
| Parmax | 矿物 (Mineral) | 180 | 300 | -10~+120 | 常温脂 Normal temperature grease | |||
| Emalube 1130 | 聚尿 (Ureal) | 矿物 (Mineral) | ≥260 | 300 | -10~+130 | 常温脂 Normal temperature grease | ||
| Unilube DL1 | 锂基 (Lithium) | 矿物 (Mineral) | 185 | 332 | -10~+110 | 常温脂 Normal temperature grease | ||
| Alumix HD1 | 矿物 (Mineral) | 247 | 335 | 0~+120 | 常温脂 Normal temperature grease | |||
| Multemp LTS | 锂基 (Lithium) | 酯 (Ester) | 250 | 201 | -60~+130 | 低温脂 Low-temperature grease | ||
| Multemp SRH | 锂基 (Lithium) | 酯 (Ester) | 250 | 201 | -40~+150 | 低温脂 Low-temperature grease | ||
| Multemp SB-M | 双聚尿 (Diurea) | 合成油 (Synthetic oil) | 220 | 260 | -40~+200 | 商温高速脂 High temperature high speed grease |
||
| Multemp SC-C | 双聚尿 (Diurea) | 合成油 (Synthetic oil) | 280 | 300 | -40~+200 | 高温水泵脂 High temperature pump-water grease |
||
| ET-K | 双聚尿 (Diurea) | 合成油 / 酯 (Synthetic oil/Ester) |
260 | 300 | -40~+200 | 髙温高逨交流电机脂 High temperature high speed alternators grease |
||
| Super-N | 聚尿 (Ureal) | 矿油 / 合成油 (Mineral oi|/Synthe:ico) |
254 | 251 | -40~+180 | 常温脂 Normal temperature grease | ||
| KIUber | Staburags NBU12 | 钡基 (Barium) | 矿物(Mineral) | 220 | 270 | -35~+150 | 常温脂 Normal temperature grease | |
| Isoflex NBU15 | 钡基 (Barium) | 双酯 - 矿物 (Diester Mineral) | 220 | 280 | -30~+130 | 常温脂 Normal temperature grease | ||
| Asonic GLY32 | 锂基 (Lithium) | 合成 (Synthetic) | 190 | 265~295 | -50~+140 | 低温脂 Low-temperature grease | ||
| Asonic GHY72 | Polyhamstoff | 酯 - 矿物 (Ester Mineral) | 250 | 250~280 | -40~+18 | 髙温低噪音 High temperature low noise | ||
| Isoflex Super LDS18 | 锂基 (Lithium) | 双酯 (Diester) | 190 | 280 | -60~+13 | 低温脂 Low-temperature grease | LY218 | |
| Isoflex Super TEL | 锂基 (Lithium) | 矿物 (Mineral) | -65~+70 | 低温脂 Low-temperature grease | ||||
| Isoflex LDS18 Special A | 锂基 (Lithium) | 双酯 (Diester) | 190 | 280 | -60~+130 | 低温脂 Low-temperature grease | ||
| Isoflex PDB38 CX 100 | 锂基 (Lithium) | 酯 (Ester) | -70~+120 | 低温脂 Low-temperature grease | ||||
| Isoflex Topas NB52 | 钡基 (Barium) | 合成碳氢 (Synthetic hydrocarbon) | 240 | 280 | -60~+170 | 髙、低温 High-low temperature grease | ||
| Barrierta L55/2 | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | 280 | -35~+260 | 髙、低温 High-low temperature grease | |||
| Barrierta EL | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | 280 | -50~+180 | 髙、低温 High-low temperature grease | |||
| Barrierta IMl/V | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | 280 | -50~+220 | 髙、低温 High-low temperature grease |
|||
| Unisilikon TK44N2 | Na-Komplex | 硅油 (Slicone) | -60~+230 | 髙、低温 High-low temperature grease |
||||
| Isoflex NCA15 | 特种钙 (Spec. Ca) | 酯矿油 {Ester Mineral oil) | 180 | 265~295 | -40~+130 | 高逨脂 High speed grease | ||
| Asonic HQ72-102 | 聚尿 (Ureal) | 酯 (Ester) |
240 | 250~280 | -40~+180 | 髙、低温低噪音脂 High-low temperature and low ocmse grease |
||
| PetamoGHY133 | 聚尿 (Ureal) | 合成矿油 （Synthetic Mineral oil) |
240 | 250~280 | -25~+150 | 常温脂 Hormal temperature grease | ||
| Petamo GHY443 | 聚尿 (Ureal) | 酯 (Ester) | 250 | 250~280 | -20~+180 | 髙温长寿命脂 High temperature longevity grease |
||
| Dow Coming |
Molykote 33M | 锂基 (Lithium) | 硅油 (Silicone) | 210 | 260 | -70~+180 | 髙、低温 High-low temperature grease | LY81 |
| Molykote 44M | 锂基 (Lithium) | 硅油 (Silicone) |
204 | 260 | -40~+200 | 髙温脂 High temperature grease | LY13 | |
| Molykote 55M | 锂基 (Lithium) | 硅油 (Silicone) | -55~+165 | 低温脂 Low-temperature grease | LV52 |
# 油脂列表
| 制作厂 Manufacturer |
牌号 Brand |
增稠剂 Viscosity |
基油 Base oil |
滴点 Drop point℃ |
稠度 Consistency |
使用温度范围 Operating termperature range |
选用原则 Selection criteria |
代码 |
| Dow Corning |
Molykote BR2 plus | 锂基 (Lithium) | 矿物 (Mineral) | 280 | -30~+150 | 高速脂 High speed grease | ||
| Molykote FS1292 | 聚四氟乙烯 (PTFE) | 硅 (PhlorosiIicon) | ≥232 | 310 | -40~+200 | 髙温脂 High temperature grease | LY59 | |
| Molykote FS3451 | 聚四氟乙烯 (PTFE) | 硅 (PhlorosiIicon) | ≥260 | 285 | -40~+230 | 抗化学溶剂脂 Chemicorl and solnent-resisiant grease |
||
| MoJykote EM50L | 锂基 (Lithium) | 合成油 (Synthetic oil) | 195 | 325 | -40~+150 | 低噪音脂 Low noise grease | ||
| Molykote BG20 | 锂基 (Lithium) | 合成油 (Synthetic oil) | 230 | 265~295 | -50~+180 | 髙温高速脂 High temperature high speed grease | ||
| Shell | Alvania No.2 | 锂基 (Lithium) | 矿物 (Mineral) | 182 | 272 | -25~+120 | 常温脂 Normal temperature grease | LY83 |
| Alvania No.3 | 锂基 (Lithium) | 矿物 (Mineral) | 183 | 233 | -20~+135 | 常温脂 Normal temperature grease | ||
| Alvania RA | 锂基 (Lithium) | 矿物 (Mineral) | 183 | 252 | -25~+120 | 常温脂 Normal temperature grease | ||
| Afvania EP2 | 锂基 (Lithium) | 矿物 (Mineral) | 185 | 276 | -10~+100 | 常温脂 Normal temperature grease | ||
| Sunlight 2 | 锂基 (Lithium) | 矿物 (Mineral) | 196 | 273 | -20~+120 | 常温脂 Normal temperature grease | ||
| Dolium R | 矿物 (Mineral) | 238 | 281 | -20~+140 | 常温脂 Normal temperature grease | |||
| Aero shell No.5 | Microgel | 矿物 (Mineral) | ≥260 | 282 | -10~+130 | 常温脂 Normal temperature grease | ||
| Aero shell No.7 | Microgel | 矿物 (Mineral) | ≥260 | 288 | -70~+150 | 重低温脂 Low-temperature grease | ||
| Aero shell No.15A | 聚四氟乙烯 (PTFE) | 双酯 (Diester) | ≥260 | 280 | -70~+260 | 高、低温 High-low Temperature grease | ||
| Alvania RLQ2 | 锂基 (Lithium) | 矿物 (Mineral) | 195 | 266 | -50~+150 | 低噪音、高速脂 Low noise、high speed grease |
||
| Mobil Oil |
Mobilux2 | 锂基 (Lithium) | 矿物 (Mineral) | 190 | 280 | -20~+120 | 常温脂 Normal temperature grease | |
| Mobil 22 | 锂基 (Lithium) | 双酯 - 矿物 （Diester Mineral) |
192 | 274 | -50~+140 | 低温脂 Low-temperature grease | ||
| Mobil 28 | 膨润土 (Bentonite) | 合成碳氢 (Synthetic hydrocarbon) |
≥260 | 280 | -60~+180 | 高、低温 High-low temperature grease | LY48 | |
| Mobilplex 47 | 矿物 (Mineral) | ≥260 | 280 | -20~+120 | 常温脂 Normal temperature grease | |||
| Mobilth SHC100 | 锂基 (Lithium) | 合成油 (Synthetic oil) | 250 | 265~295 | -40~+170 | 高速脂 High speed grease | ||
| Mobilth SHC220 | 锂基 (Lithium) | 合成油 (Synthetic oil) | 250 | 265~295 | -40~+170 | 多用途脂 Multiple use grease | ||
| Mobilitemp SHC22 | 粘土 (glue-earth) | 合成油（Synthetic oil) | 250 | 265~295 | -50~+180 | 高速、高温脂 High speed high temperature grease |
||
| Mobilitemp SHC100 | 粘土 (glue-earth) | 合成油（Synthetic oil) | 250 | 265~295 | -50~+200 | 高速、高温脂 High speed high temperature grease |
||
| Du Pont |
Krytox 204AC | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | 282 | -35~+280 | 高温脂 High temperature grease | LV101 | |
| Krytox 283AC | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | 229 | -35~+280 | 高温脂 High temperature grease | |||
| Krytox 143AC | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | -35~+280 | 高温脂 High temperature grease | ||||
| Kfytox GPL205 | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | -36~+204 | 高温脂 High temperature grease | ||||
| Krytox GPL223 | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | -36~+204 | 高温、发电机、风扇离合器轴承脂 High temperature, alternator fan clutch bearing grease |
||||
| Krytox GPL224 | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | -51~+179 | 高温、发电机、风扇离合器轴承脂 High temperature, alternator fan clutch bearing grease |
||||
| Krytox GPL225 | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | -60~+154 | 气泵轴承脂 High temperature grease | ||||
| Krytox GPL226 | 聚四氟乙烯 (PTFE) | 氟化油（Fluoriaated) | -36~+260 | CV 万向节 CV joint | ||||
| Toray Silicone |
SH44M | 锂基 (Lithium) | 硅 (PhlorosiIicon) | 210 | 260 | -40~+180 | 高温脂 High temperature grease | LY115 |
| SH33L | 锂基 (Lithium) | 硅 (PhlorosiIicon) | 210 | 300 | -70~+140 | 低温脂 Low-temperature grease | ||
| SH41 | 锂基 (Lithium) | 硅 (PhlorosiIicon) | 280 | -10~+200 | 高温脂 High temperature grease | |||
| Caltex | Chevron SRI-2 | 聚尿 (Urea) | 矿物 (Mineral) | 293 | 30~+175 | 高温脂 High temperature grease | LY75 | |
| General Electric |
Anderol L-793A | 锂基 (Lithium) | 双脂 (Diester) | -60~+150 | 低温脂 Low-temperature grease | |||
| Versilube G-300 | 锂基 (Lithium) | 硅油 (Silicone) | -70~+230 | 高、低温 High-low temperature grease | ||||
| Versilube F-50 | 硅油 (Silicone) | -70~+230 | 高、低温 High-low temperature grease | LY15 | Lubcon | Turmogrease N2 | 聚尿 (PoIyurea) | 合成油 / 酯 (PAO/Ester) | ≥250 | 280 | -40~+160 | 通用轴承 Currency bearing | LY5 |
| Lubteksonic BQg | 锂基 (Lithium) | 矿物 (Mineral) | 250 | 280 | -35~+150 | 低噪音 Low noise | ||
| Turmogrease SHL182 | 锂基 (Lithium) | 合成油 / 酯 (PAO/Ester) | 250 | 280 | -70-~+130 | 低温高速脂 Low temperature high speed grease | ||
| Turmogrease SHL 252 | 特种锂基 (Lithium) | 合成油 / 酯 (PAO/Ester) | 220 | 280 | -40~+120 | 高速脂 High speed grease | ||
| Turmoplex TML15 | 铧基（Lithiu ㈣ | 酯 (Ester) | 290 | 280 | -35~+160(180) | 高温高速脂 High temperature high speed grease |
||
| Turmogrease CX112K | 锂基 (Lithium) | 矿油 / 合成油 (Mineral oi|/Synthe:ico) |
190 | 265~295 | -35~+140(160) | 低噪音 Low noise | ||
| Turmogrease NBI 300 | 聚尿 (PoIyurea) | 合成油脂 (PAO/Ester) | 250 | 280 | -40~+180 | 高温离负荷脂 High temperature high load grease |
||
| Lubchem | Chevron SRI-2 | 聚尿 (PoIyurea) | 多元醇 (Polyols) | 280 | 250 | -40~+200 | 髙温脂 High temperature grease |
版权所有 © 2014 - 浙江通泰轴承股份有限公司